How To Prepare Specifications For A Custom Electronic Transformer

Sep 29, 2026 Leave a message

When requesting a custom electronic transformer, providing only the input voltage, output voltage, and rated power is rarely enough to obtain an accurate design or quotation.

A transformer manufacturer also needs to understand how the component will operate inside the circuit. Switching frequency, converter topology, load conditions, isolation requirements, winding characteristics, operating temperature, and installation space can all affect the final construction.

Missing information often leads to repeated clarification, revised samples, or unexpected differences between the proposed transformer and the customer's actual application.

A useful custom electronic transformer specification does not need to contain every design calculation. It needs to clearly separate the requirements that the transformer must meet from the details that the manufacturer can propose.

This guide explains what to include in a transformer specification, which parameters matter for different transformer types, and how to prepare an RFQ that supports a more efficient engineering review.

1. Start with the Application and Transformer Type

Before listing electrical parameters, explain what the transformer does in the equipment.

A transformer used in an isolated flyback power supply has different design requirements from a pulse transformer used for gate driving or a current transformer used for current sensing.

Identify the intended type and application:

Transformer type Application information to provide
High-frequency switching transformer Converter topology, switching frequency, input range, output power, and isolation requirement
Low-frequency transformer AC input frequency, primary and secondary voltages, load rating, and duty cycle
Pulse transformer Pulse amplitude, pulse width, repetition frequency, rise/fall time, and load impedance
SMD transformer Circuit function, operating frequency, power or signal level, PCB footprint, and assembly restrictions
Current transformer (CT) Primary current range, secondary current or voltage, burden resistance, frequency, and accuracy
Potential transformer (PT) Primary and secondary voltage, frequency, accuracy class, burden, and insulation requirements
Signal or communication transformer Signal frequency range, impedance, insertion loss, isolation, and common-mode requirements

Do not rely on the product name alone. Terms such as high-frequency transformer, pulse transformer, and signal transformer cover different electrical operating conditions.

If the transformer is intended to replace an existing component, include its part number, datasheet, label photograph, connection diagram, and any known performance issues. A reference component gives the manufacturer a useful starting point, but it should not replace the new application's requirements.

electronic-transformer-core-and-winding-assembly

2. Define the Electrical Input and Output Requirements

The input and output specifications are the foundation of the transformer design. They should describe the actual operating range rather than only nominal values.

For the primary side, specify:

Input voltage: minimum, nominal, and maximum

AC or DC input

Input waveform, where relevant

Operating frequency or switching frequency range

Maximum duty cycle, if applicable

Startup, transient, or abnormal operating conditions that affect the transformer

For each secondary winding, provide:

  • Required output voltage
  • Continuous and peak current
  • Output power
  • Load type and operating profile
  • Whether outputs operate simultaneously
  • Required regulation or voltage tolerance
  • Any center tap or multiple-output arrangement

For example, a transformer with two secondary windings may have a different thermal requirement when both outputs are loaded simultaneously than when each output is tested separately.

A useful specification should state whether the output voltage is measured at no load, rated load, or another defined condition. If the voltage is specified at the transformer terminals or after a rectifier and regulator, make that distinction clear.

For switching power supplies, the output voltage after the secondary rectifier is not the same as the transformer's winding voltage. The circuit configuration and measurement point should be identified.

3. Specify the Switching Frequency and Converter Topology

For a high-frequency electronic transformer, switching frequency is one of the most important design inputs.

Provide the nominal switching frequency and its operating range. If the controller uses frequency modulation, burst mode, pulse skipping, or a wide load-dependent frequency range, include that information.

Also identify the converter topology, such as:

Flyback

Forward

Push-pull

Half-bridge

Full-bridge

LLC resonant converter

Gate-drive circuit

The topology affects the transformer's magnetic waveform, flux excursion, winding arrangement, and electrical stress.

For example, a flyback transformer stores energy during one switching interval and transfers it to the secondary during another. Its design requirements differ from those of a forward transformer, where energy transfer takes place through transformer action during the active switching interval.

An LLC transformer may use leakage inductance as part of the resonant tank. Therefore, specifying the lowest possible leakage inductance is not always correct.

If the converter is already designed, provide the schematic or relevant controller information when possible. If the transformer manufacturer is expected to help develop the magnetic design, identify which circuit parameters are fixed and which can be adjusted.

4. State the Required Magnetic Parameters

Electrical ratings alone may not fully describe a high-frequency transformer. Certain magnetic parameters need to be specified or agreed upon during the design review.

The most relevant parameters often include:

Parameter What to specify or confirm Why it matters
Turns ratio Primary-to-secondary ratio and tolerance Determines the voltage relationship between windings
Magnetizing inductance Target value, tolerance, and measurement conditions Affects magnetizing current and converter operation
Leakage inductance Maximum, minimum, or target value as required by the topology Influences switching spikes, ringing, and resonant behavior
DC resistance (DCR) Per-winding maximum or target value Helps evaluate winding loss and voltage drop
Interwinding capacitance Maximum or target value when important Affects common-mode noise and high-frequency behavior
Polarity or phasing Winding dot convention and terminal identification Prevents incorrect connections and phase relationships
Core material Required grade, approved alternatives, or manufacturer proposal Influences core loss, saturation margin, and temperature behavior

A critical point is that measurement conditions should accompany magnetic parameter limits.

For example, magnetizing inductance and leakage inductance can depend on test frequency, test voltage, instrument settings, and the condition of the other winding. A specification that states only "leakage inductance below 10 μH" may produce inconsistent results if the measurement method is not defined.

For leakage inductance, identify which winding is energized and which winding is short-circuited. For magnetizing inductance, state the test frequency and relevant test conditions.

If the design has not yet established these parameters, mark them as "manufacturer to propose" rather than inserting arbitrary values.

custom-transformer-electrical-parameter-testing

5. Define the Insulation and Safety Requirements

Insulation requirements should be stated early because they can influence the winding arrangement, bobbin, wire selection, insulation materials, terminal spacing, and overall dimensions.

For an isolated electronic transformer, identify:

Working voltage: The continuous voltage between isolated circuits under normal operation.

Dielectric withstand voltage: The required test voltage, duration, and test configuration between specified windings or conductive parts.

Insulation system: Whether functional, basic, supplementary, double, or reinforced insulation is required.

Creepage and clearance: The required distances between primary and secondary conductive parts, including relevant terminal and PCB layout considerations.

Insulation resistance: The required minimum value and test conditions, if specified by the application.

Applicable standards: The exact product safety standard or project requirement, including the relevant edition where known.

Do not write only "high insulation" or "high-voltage isolation." These descriptions are too vague for engineering review.

For example, a transformer used in an isolated AC-DC power supply may require reinforced insulation, while a signal transformer may have a different isolation requirement. The applicable standard depends on the end product and its operating environment.

The dielectric test voltage should not be treated as the working voltage. They describe different conditions and must be specified separately.

If the transformer is intended for a certified product, tell the manufacturer the end-product standard and certification requirements. Component-level documentation should be checked against the actual insulation system and intended use.

electronic-transformer-hipot-insulation-testing

6. Include the Operating Temperature and Cooling Conditions

A custom transformer must operate within its thermal limits under the real conditions inside the finished equipment.

Specify:

Minimum and maximum ambient temperature

Expected continuous operating temperature

Maximum permitted temperature rise, if established

Continuous or intermittent duty

Natural convection or forced-air cooling

Nearby heat sources

Enclosure and ventilation conditions

The transformer manufacturer needs to consider both core loss and winding loss.

For high-frequency transformers, core material and flux density influence core loss. Winding conductor size, current, winding arrangement, and frequency affect copper loss. A design that meets its electrical ratings on paper may still experience excessive temperature rise when installed in a compact enclosure.

If the transformer operates at high ambient temperature or near power semiconductors and heat sinks, provide that information. Testing an open-frame sample in free air may not represent the final product's thermal environment.

Where the temperature-rise limit has not been established, ask the manufacturer to propose a design and provide the test conditions used to verify it.

7. Provide Mechanical Dimensions and Mounting Requirements

Mechanical information is essential for a custom transformer because even a well-performing electrical design may be unusable if it does not fit the equipment.

Provide a maximum envelope rather than an approximate visual estimate.

Important details include:

Maximum length, width, and height

Core or bobbin orientation

Mounting method

Pin count and pin spacing

Pin diameter or terminal dimensions

PCB footprint or mounting drawing

Terminal identification and polarity

Required clearance from nearby components

Weight limit, if relevant

Encapsulation or housing requirements

For SMD transformers, include the PCB land pattern, terminal configuration, component height limit, and assembly process. If the component will undergo reflow soldering, identify the relevant soldering profile and any component handling requirements.

For through-hole transformers, specify the pin arrangement, pitch, insertion direction, and any mechanical support requirements.

If the transformer must fit an existing PCB, provide the actual PCB drawing or a dimensioned footprint. A photograph alone is not sufficient to confirm pin spacing and mechanical compatibility.

8. Specify Winding Construction and Material Requirements Only When Necessary

Some customers have specific requirements for winding materials or construction. These should be included when they are necessary for electrical performance, insulation, regulatory compliance, or compatibility with the existing product.

Relevant details may include:

Copper wire or litz wire

Triple-insulated wire

Sectioned or split-bobbin winding

Interleaved primary and secondary windings

Electrostatic shielding

Shield termination

Insulation tape or barrier materials

Potting or encapsulation

Core material or core shape

However, it is not always necessary for the customer to specify every internal construction detail.

For a new custom transformer, the manufacturer may be better positioned to recommend the core size, wire gauge, winding arrangement, and insulation structure after reviewing the electrical and mechanical requirements.

A practical approach is to distinguish mandatory requirements from design preferences.

For example:

Mandatory: reinforced insulation between primary and secondary.

Mandatory: maximum overall height of 18 mm.

Preferred: EFD core construction.

Manufacturer to propose: core material, wire size, and winding arrangement.

This gives the manufacturer room to optimize the design without compromising the customer's essential requirements.

electronic-transformer-ferrite-core-assembly

9. Define Inspection, Testing, and Acceptance Criteria

A specification should explain how the finished transformer will be checked. Otherwise, the manufacturer and buyer may use different criteria when deciding whether a sample or production batch is acceptable.

Depending on the transformer type, the inspection plan may include:

Test or inspection Typical purpose
Turns ratio and polarity Verify winding ratio and connection direction
Inductance Confirm magnetizing or other specified inductance
Leakage inductance Verify coupling-related performance
DC resistance Check winding resistance
Dielectric withstand test Verify insulation withstand performance
Insulation resistance Evaluate insulation resistance under defined conditions
Interwinding capacitance Check capacitive coupling where required
Visual inspection Check winding condition, core assembly, terminals, and workmanship
Dimensional inspection Confirm mechanical compatibility
Temperature-rise test Verify thermal performance under defined operating conditions

Not every transformer requires every test. The test plan should match the application and applicable standards.

For example, a pulse transformer may require pulse waveform verification, while a current transformer may require ratio error, phase error, and burden-related accuracy checks.

For production orders, distinguish between routine tests performed on each unit, sample-based inspections, and type tests performed to validate a design. If a test report is required, specify its format and whether it must be supplied with every shipment or only during qualification.

Acceptance criteria should include tolerances and measurement conditions. "Check inductance" is not an acceptance criterion unless the target value, tolerance, and test method are defined.

10. Separate Prototype Requirements from Mass Production Requirements

A custom transformer project usually involves more than one delivery stage. The sample specification and production specification should be aligned, but their quantities and approval requirements may differ.

When requesting a quotation, provide:

Initial prototype quantity

Engineering sample quantity

Expected first production quantity

Estimated annual demand

Expected order frequency

Target sample date

Target mass-production date

If the design is still under development, state which parameters may change after testing.

Before mass production, confirm the approved drawing, electrical specification, material requirements, test plan, and revision number. Any later change to winding construction, core material, insulation materials, or mechanical dimensions should be reviewed before implementation.

This is particularly important when the transformer is a custom replacement for an existing component. A change that appears minor to the manufacturer may affect the customer's PCB, thermal performance, or safety evaluation.

11. A Practical RFQ Checklist for Custom Electronic Transformers

The following checklist can be used when preparing a transformer inquiry. Mark unavailable information as "TBC" rather than guessing.

Section Information to provide
Application Product name, circuit function, and intended use
Transformer type High-frequency, low-frequency, pulse, SMD, CT, PT, or signal transformer
Input Voltage range, AC/DC, waveform, and frequency
Output Voltage, current, power, and number of secondary windings
Converter details Topology, switching frequency, duty cycle, and schematic if available
Magnetic parameters Turns ratio, inductance, leakage inductance, DCR, and capacitance requirements
Insulation Working voltage, dielectric test, insulation class, and applicable standard
Thermal Ambient temperature, cooling conditions, and temperature-rise target
Mechanical Maximum dimensions, mounting style, pin layout, and drawing
Materials Mandatory material or construction requirements, if any
Testing Required electrical, insulation, thermal, and dimensional tests
Commercial Sample quantity, production quantity, annual demand, and target delivery schedule
Documentation Datasheet, drawings, test reports, material declarations, and revision control

A complete RFQ should also identify which values are fixed, which have acceptable tolerances, and which are open for the manufacturer to propose.

12. Frequently Asked Questions

Q1: What information is essential for a custom transformer quotation?

At minimum, provide the application, transformer type, input voltage, output voltage and current, operating frequency, power requirement, insulation requirement, maximum dimensions, and expected quantity. For switching transformers, also identify the converter topology and switching frequency.

Q2: Do I need to provide the core material and wire size?

Not necessarily. If the design is new, the manufacturer can often recommend the core material, core geometry, wire size, and winding arrangement. Specify them only when they are mandatory or when you are reproducing an existing approved design.

Q3: Can I request a custom transformer using only a sample?

A physical sample is a useful reference, especially for dimensions, terminal layout, and construction. However, it may not reveal all electrical parameters or insulation requirements. Provide the original datasheet, circuit information, test results, or known operating conditions whenever possible.

Q4: Should leakage inductance and magnetizing inductance be included in the specification?

Yes, when they affect the converter's operation. State the target or acceptable range together with the measurement conditions. If the values are not yet established, ask the manufacturer to propose them based on the circuit requirements.

Q5: How should I specify the insulation requirement?

Identify the working voltage, required insulation system, dielectric withstand test voltage and duration, creepage and clearance requirements, and applicable end-product standard. Avoid relying on descriptions such as "high isolation" without measurable requirements.

Q6: Why does the manufacturer need the operating temperature?

Core loss and winding loss generate heat, and the final temperature depends on ambient conditions, enclosure design, airflow, and loading. Without this information, the manufacturer may evaluate the transformer under conditions that do not match the finished equipment.

Q7: What should I confirm before approving a transformer sample?

Check the approved electrical parameters, winding polarity, mechanical dimensions, insulation performance, and thermal behavior under representative operating conditions. Also confirm that the sample matches the intended production construction and revision.

Conclusion

Preparing a good specification for a custom electronic transformer is about communicating the complete operating conditions, not simply listing a few voltage and power values.

A useful specification defines the circuit application, electrical input and output, operating frequency, magnetic requirements, insulation, thermal conditions, mechanical limits, and acceptance tests. It also makes clear which parameters are mandatory and which can be proposed by the manufacturer.

When the manufacturer receives this information before design work begins, it becomes easier to assess feasibility, select a suitable magnetic structure, identify missing requirements, and provide a quotation that reflects the actual application.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry